bac water
#reconstitution 2025-04-13
- appetite_back — temperature of the diluent does not matter. how fast you push it in does 17:50
- coa_or_cope — aim the diluent at the glass wall, not at the powder. it goes in gentler 17:52
- dorm_fridge — i have never once regretted using a rounder number and a slightly bigger volume 18:58
- gradient_greg — weighing the vial before you reconstitute is the only way to catch an underfill 19:24
- VialBot — Batch lookup H-2814: 7 independent reports on file, earliest 2024-09-24. 21:15
Purity check: no report on file for lot B-0114. Nothing logged either way.
one unit is 0.01ml
can i add more bac water later to a vial ive already reconstituted
i write the mg/ml on the vial with a sharpie the moment i reconstitute it
temperature of the diluent does not matter. how fast you push it in does
im getting bubbles in the barrel every single time, what am i doing wrong
aim the diluent at the glass wall, not at the powder. it goes in gentler
lyophilised powder is far more robust than people think. it is the solution that is fragile
do you let it come to room temp before drawing or draw it cold
how long after reconstituting before its actually dissolved
yep 10 units
10mg vial
+ 1.0ml -> 10.0 mg/ml 0.5mg = 5u 1mg = 10u
+ 2.0ml -> 5.0 mg/ml 0.5mg = 10u 1mg = 20u
+ 2.5ml -> 4.0 mg/ml 0.5mg = 12.5u (dont)
+ 5.0ml -> 2.0 mg/ml 0.5mg = 25u 1mg = 50uif i add 0.5ml to a 15mg vial what concentration am i actually at
not sterile water
label the vial
10mg in 2ml is 5mg/ml. so 0.5mg is 0.1ml which is 10 units on a u100
too dilute imo
On this day 9 years ago this channel logged 140 messages.
if the powder is on the stopper, tap it down before you add anything. it will still dissolve either way
do not add more bac water to an already reconstituted vial, you have lost track of the concentration
while im here i use bac water even for a single-use vial because it stings less, which is not the reason it exists
[edited]thats 5mg/ml
i have never once regretted using a rounder number and a slightly bigger volume
i swirl for about thirty seconds and then leave it. never had one fail to dissolve
15mg in 3ml is 5mg/ml. same numbers as 10 in 2, just more of it
does it matter if i inject the bac water straight at the powder
the meniscus thing is real. read it at eye level or you are guessing by a unit either way, i have it written down somewhere
update from 16 months ago: switched to a single concentration and have not miscalculated since
weighing the vial before you reconstitute is the only way to catch an underfill
do i swirl for a specific length of time or just until its clear
my rule is one concentration for everything so i never have to think about it at 7am
20mg in 2ml is 10mg/ml. 1mg is 10 units, 2mg is 20 units, easy
nope, redo it
how do you all measure a half unit, or do you just not
while im here took me a year to stop over-diluting. the measurement error at 4 units is worse than the convenience, from memory
foam is bad
thats the vacuum
write the date on
5mg in 2ml gives 2.5mg/ml, 0.25mg is 10 units. good for a starting dose
thats fine
bac water or sterile water for something im going into weekly for 6 weeks
if you cannot read the mark confidently, your volume is too small. redo it at a lower concentration
one unit is 0.01ml. 100 units is 1ml. everything else in this channel follows from that
my 10mg vial weighed 11.4g on the jewellery scale, is that wrong
the last few units are a real loss. i accept it rather than tilting the vial and drawing air
for the archive 30mg in 3ml is 10mg/ml, so 5mg is 50 units. half the barrel, feels like a lot but its right, i could be wrong
weigh it first
the vacuum will pull it in. let it. fighting it is how you get a face full of aerosol
the powder is stuck to the stopper, do i care
[edited]bacteriostatic water for anything multi-use. sterile water has no preservative in it at all
Batch lookup H-2814: 7 independent reports on file, earliest 2024-09-24.
it foamed. is it ruined
is it worth buying a 3ml syringe for the diluent or is the insulin one fine
round numbers